| Explosives information bulletin | No.11 V 2 | 20 September 2007
Precautions against flyrock
Purpose
Flyrock can best be defined as, the undesirable throw of debris from a blast. It is generally found to originate around the collar of the blast hole or the face of a blast and to have been caused by incorrect selection or application of burden, stemming length or by blast holes being initiated out of sequence.
Because the potential for severe injury or property damage exists, precautions against flyrock must be foremost in the mind of the blast designer and shotfirer. The closer to persons or property that blasting is carried out, the greater the awareness, care and degree of protection exercised in avoiding incidents of flyrock.
Issues
Examination of blast site
One important consideration often overlooked, is the structure of the rock. Fissures, joints and weakness planes are not necessarily the same from location to location even within the same blast area. Because weathering of the surface rock is generally more pronounced than in the deeper lying strata, it is important that the surface rock is inspected for faults and planes which are likely to assist in the creation of flyrock. Previous excavations can give significant information about the rock structure, as can information from the driller of the blast holes.
Area surrounding the blast site must be inspected to determine distances to protected works eg : residences, roads, public places, dangerous goods storage and due consideration of same must be taken in determining the degree of protection necessary.
Blast design
Good blast design is generally the primary method of avoiding flyrock.
- Select the direction of blasting face so as to place any person or buildings at the rear of the face.
- Avoid shallow blasting that is generally less than 1 metre. It must be remembered that the surface provides a free face. Ensure a blast ratio (tonnes of rock per kilogram of explosives) sufficiently high to eliminate the possibility of excessive charging. Use smaller hole diameters where possible.
- Choose a burden of sufficient magnitude to reduce the possibility of blast through (generally, between one third to half the depth of holes).
- In general, keep the stemming length not less than 25 times the blast hole diameter or not less than the burden, whichever is the greater. Stemming material must be free from rocks and properly tamped.
- Where possible use sequential or delay firing so that all shots fire from the face backwards. The delay sequence should be carefully checked.
- Take special care when carrying out secondary blasting to avoid overcharging.
Note: Trench blasting and blasting where bench heights are small compared to the burden are commonly regarded as providing greatest potential for flyrock because the degree of confinement and the specific charge are high and the charge is sometimes placed close to the surface.
Drilling and loading
While the blast pattern generally determined by experience may be satisfactory, inaccuracies in drilling or incorrect blast hole angle can cause quite large deviations from the planned pattern with excessive noise, vibrations and/or flyrock resulting. The extra time spent on making sure that the blasthole is in the right position is especially warranted. Instruments should be used to set out the drilling pattern. There will be difficulty in estimating the burden in hilly terrain.
The correct charge weight must be employed in the blast hole. When using ANFO or any other free running explosive, pour measured quantities of the explosives into the hole and monitor the build up of the explosive column by tape measure or wooden pole. This is to avoid overcharging which may result from fissures or chambers in the rock.
Cover
Where any doubt exists, or where the blast situation demands added precautions eg : shallow blasting or proximity to protected works, sufficient cover must be placed on the blast to further minimise the possibility of resulting flyrock.
Where backfilling is used to cover loaded holes this should be sorted material without stones. The cover should be placed with care to avoid damage to connecting wires, shock tube or detonating cord trunklines and should be to a minimum depth, which would eliminate flyrock.
If using blasting mats to provide cover, the following precautions should be observed:
- A layer of sand or sandbags should cover the rock at least in the area of the hole collar, to protect the mat from being damaged.
- Only the number of holes that can be adequately covered by blasting mats should be loaded and fired at one time. Mats should be anchored where practicable.
- Rock or debris should not be placed on top of the mats, as these may become missiles.
- Long delay or multiple delay safety fuse firing should not be used where mats are depended upon to contain flyrock as the first firing holes may strip the mats off the remaining unfired holes.
- Mats of wire rope or steel ring should not be used in the vicinity of overhead power lines.
- Care must be taken when laying mats so that connecting wires, shock tube or detonating cord trunklines will not be damaged.
Experience has shown that nearly all incidents of flyrock could have been avoided if the proper precautions had been taken. It is the responsibility of the blast designer and the Shotfirer to ensure that due consideration is given to the prevention of flyrock from the early stages of blast planning and that all necessary steps are taken to minimise its occurrence. It may also be necessary to close off roads, walkways etc, during a blast to ensure flyrock is not a risk to the community.
Failure to adhere to normal safety practices in this regard is a breach of the duty of care principle and may jeopardise licences granted by the Chief Inspector of Explosives in Queensland.
References
A. Australian Standard AS2187 Part 2, Use of Explosives.
Contact: explosives@dnrm.qld.gov.au
Issued by Queensland Department of Mines and Energy
Find more Safety and Health Alerts
Search the hazards database